HDC Firmware Download

HDC Firmware v2.61.0

Feature Updates
  • Page 49,50 F/R status OUT signal change (Forward :1, Reverse:0 --> Forward:0, Reverse:1)
  • Page 20 UP button is available to select Model no. when P75 is enabled.
  • Operation change / Unless other model no. was not selected, the latest loaded model no. is
  • continuously effective even if it's program was changed.
  • Page 12 The lowest torque setting range is changed from 7 to 5 Kgf.cm for HD220 & HD220P.
PC Software

Version2.61.0
Size260.39 KB
Downloaded26 times
Create Updated2015-04-06
Please login

HDC Firmware v2.60.2

Feature Updates
  • parmeter P98 added : Start signal OFF delay time  Requested by Doga.
  • Customer lost the fastening OK output when operator release start lever just before torque up, but clutch was activated by innertia. range : 0 - 1,000 mS  factory setting : 10mS
  • Motor immediate stop by breaking when start signal OFF
PC Software

Version2.60.2
Size260.12 KB
Downloaded6 times
Create Updated2014-11-13
Please login

HDC Firmware v2.60.0b

Feature Updates
  • Automatic parmater reset to factory setting feature deleted when the driver model is replaced.
  • Manual paremeter reset is required when the driver is replaced with the different model of driver.
  • P59 : Factory setting is changed from "0" (USB) to "1" (RS232C) when initialized
PC Software

Version2.60.0b
Size259.12 KB
Downloaded4 times
Create Updated2014-10-13
Please login

HDC Firmware v2.58.5

Feature Updates
  • LG- requested
PC Software

Version2.58.5
Size258.11 KB
Downloaded3 times
Create Updated2014-09-03
Please login

HDC Firmware v2.58.2

Feature Updates
  • Torque range modification of HD081 2.5 - 8.0Kgf.cm --> 2.5 - 8.3Kgf.cm by request of Doga
PC Software

Version2.58.2
Size257.51 KB
Downloaded2 times
Create Updated2014-07-07
Please login

HDC Firmware v2.58.0

Feature Updates
  • Bit socket tray - selectable socket no. on P50
PC Software

Version2.58.0
Size257.50 KB
Downloaded3 times
Create Updated2014-05-30
Please login

HDC Firmware v2.57.0

Feature Updates
  • SCAN TIME change to 0.5s from 1.0s in programing for short torque up signal time of HDC-35i
PC Software

Version2.57.0
Size257.11 KB
Downloaded2 times
Create Updated2014-05-22
Please login

HDC Firmware v2.56.2

Feature Updates
  • P88 : Soft/Hard joint select feature removed.
  • P88 : Driver Lock (I/O) feature in direction
    - 0 : Both direction
    - 1 : Reverse direction Lock only
    - 2 : Forward direction Lock only
PC Software

Version2.56.2
Size256.51 KB
Downloaded3 times
Create Updated2014-02-07
Please login

HDC Firmware v2.56.0

Feature Updates
  •  by Jabil request ( Only for V2J version )
    - V2 has same torque formula with V1 in FW
    - New torque spec of HD060V2J: 1.9~4.2 lbf.in
PC Software

Version2.56.0
Size258.71 KB
Downloaded1 times
Create Updated2013-12-19
Please login

HDC Firmware v2.55.1

Feature Updates
  • New torque formula for V2J version in Jabil.
  • EZ-Torq II with Sehan RDA, Asian filter setting
PC Software

Version2.55.1
Size230.50 KB
Downloaded1 times
Create Updated2013-10-08
Please login